The current name of this bool is kinda stupid. Based on the manpage
setting it to 0 turns off fcoe, which means that nofcoe=1 should mean
that it is on.
Let's just do the same thing as with rd.lvm=0, rd.luks=0,....
When terminating a system, the shutdown module attempts to unmount all
file systems from under /oldroot. This reaps remaining file systems that
systemd cannot unmount and detaches /oldroot itself.
In case that running umount for some file system repeatedly fails, the
module reports this error and continues the processing in order to
shutdown the system. This handles a condition when the umount command
actually terminates but it can happen in some cases that it waits
indefinitely.
An example with NFS mounts:
# mount -t nfs 192.168.0.1:/srv/nfs/dir /mnt/nfs
# mkdir /mnt/nfs/dir2
# mount -t nfs 192.168.0.1:/srv/nfs/dir2 /mnt/nfs/dir2
# touch /mnt/nfs/dir2/file
# systemd-run -pKillMode=none -pSendSIGKILL=no tail -f /mnt/nfs/dir2/file
Running as unit: run-r367825c967ca4d88a793ae4793c02f8b.service
# systemctl poweroff
The invoked tail command escapes normal termination by systemd and
prevents stopping mnt-nfs.mount and mnt-nfs-dir2.mount as it makes the
mounts busy. Systemd then again attempts to unmount these file systems
in systemd-shutdown but this fails as well. The utility tries to unmount
/mnt/nfs/dir2 but the kernel waits indefinitely doing a path lookup for
/mnt/nfs because network is no longer available at that point. The
systemd-shutdown gives up after 90 seconds. Finally, the control is
transferred to dracut which tries to unmount the file systems in the
same way and ends up indefinitely waiting on umount to finish.
This situation causes that the system hangs during shutdown. The patch
improves the shutdown module to add a timeout of 90 seconds for the
umount operation and continue with the shutdown if it gets reached,
similarly to what systemd-shutdown does.
We can drastically improve boot times on some machines, or BM or VM
shapes, if we send DHCP requests in parallel on all interfaces
Add ip=single-dhcp as a kernel boot parameter, to send DHCP requests in
parallel on all interfaces. Thus, DHCP on each interface is overlapped
thereby reducing boot times for multiple interface machines.
This can help reduce the boot time by 1 minute per interface.
In addition, we may also save another 40 secs delay per interface, if
the link on which we try to send DHCP is in DOWN state. This can be
reduced by giving the following kernel command line parameter while
booting - rd.net.timeout.carrier=<timeout>.
Added manpage for ip=single-dhcp with the caveat that it does not
apply to Network Manager or SUSE wicked.
Signed-off-by: Anjali Kulkarni <anjali.k.kulkarni@oracle.com>
Introduce prefix `keysource:` for the values of `rd.luks.partuuid`,
`rd.luks.serial` and `rd.luks.uuid`.
If specified, ask for passphrase instead of waiting for keydevs to come
online.
This feature could be off loaded to memstrack, which have better
accurecy, better performance, and have more detailed tracing features.
Also simplify make_trace_mem a bit.
And currently rd.memdebug=4 is unstable, fails from time to time.
qeth device may have a different IP for each boot, so the rd.ifname=
option will no longer work. So for znet device, introduce a
rd.znet_ifname= options, to subchannel id instead of MAC address as the
identifier and rename the interface.
Signed-off-by: Kairui Song <kasong@redhat.com>
Add support for 'rd.multipath=default' for using the default
configuration on boot. The intended purpose for this is to help support
ostree-based image boots from multipathed devices (such as Fedora and
Red Hat CoreOS).
Harald Hoyer <harald@redhat.com>: Squashed commit of the following:
commit 4b5e5da6061983964a85d1671bd1c97c48ee76f1
Author: jbash aka John Bashinski <jbash@velvet.com>
Date: Thu Aug 1 13:21:35 2019 -0400
Documentation: add systemd warning for rd.luks.key, clean up related text
Images built with the fcoe module will always run the lldpad
service as part of their pre-trigger scripts if the network
is active. This prevents network installations in
environments where, for security reasons, LLDPDU frames
cause a switchport shutdown.
Add a new rd.nofcoe option to cause dracut to skip the
lldpad.sh script and the entire 95-fcoe module.
Signed-off-by: Patrick Talbert <ptalbert@redhat.com>
A simplified root filesystem structure may be provided for OverlayFS
overlays by squashing the root filesystem directly instead of squashing
an embedded image file at /LiveOS/rootfs.img. Detect and configure
such a squashed root filesystem for live booting.
For OverlayFS boots, avoid the read-only Device-mapper linear device
at /dev/mapper/live-base.
Create a consistent device link at /dev/live-base for the read-only
base loop device for all overlayed live root filesystems.
Consistently provide a link at /dev/root for wait_for_dev.
Update documentation.
Adjust sysroot.mount configuration for rd.live.overlay.overlayfs option.
Use link at /dev/root as a consistent flag for wait_for_dev.
Adjust documentation.
In kdump, if dump-target is ssh on ipv6, we need to sync until ipv6 addr
is ready. Currently ip=auto6/dhcp6 provides such function. But in 1st kernel,
it is hard to know whether the ipv6 addr is got by dhcpv6 or SLAAC.
E.g ifcfg-eth* contains DHCPV6C=yes direction, but there is no dhcpv6
server in the network, and then after the system is up, the user
echo 1 > /proc/sys/net/ipv6/conf/eth0/autoconf && accept_ra by manual
to obtain a ipv6 addr. Or vice.
So this patch suggests to make dhcpv6 as auto6 fallback
Signed-off-by: Pingfan Liu <piliu@redhat.com>
81cio_ignore: handle cio_ignore commandline
References: bnc#874902
Incorporates following on-top patches/fixes:
----------------------------
Subject: 81cio_ignore: skip module if cio_ignore is not active
When cio_ignore is not active we should skip the entire module
during boot; otherwise it'll lead to adverse effects.
References: bnc#882685
----------------------------
Subject: 81cio_ignore: rewrite module
Rewrite cio_ignore module to rely on the dracut commandline
parameter 'rd.cio_accept', which takes a comma-separated list
of CCW IDs. Each of those IDs are being removed from the
list of devices from cio_ignore.
The default values for rd.cio_accept are taken from
/boot/zipl/active_devices.txt.
References: bnc#882685
-----------------------------
Subject: More empty cmdline fixes
This fixes up some more modules which might print out empty
commandline files.
-----------------------------
Subject: Mark scripts as executable
All scripts need to be marked as executable, otherwise dracut
won't be running them.
References: bnc#887010
Signed-off-by: Thomas Renninger <trenn@suse.de>
Add new module to update the dracut commandline values
during booting with the values found in the file
dracut-cmdline.conf on the device specified by
rd.zipl.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Contrary to the original patch, this one has been modified
to check for /boot/zipl, the location of the first stage kernel
in indirect boot, in order not to install on systems
booting directly via zipl.
Signed-off-by: Daniel Molkentin <daniel.molkentin@suse.com>
FCoE can run in Fabric (ie FCF) or VN2VN mode, so we should allowing
to set this parameter from the commandline, too.
Signed-off-by: Hannes Reinecke <hare@suse.com>
When NPIV is enabled and the allow_lun_scan parameter is set to 'Y'
the HBA will initiate a LUN scan automatically, so there is no need
to specify the WWPN and LUN number manually.
References: bsc#964456
Signed-off-by: Hannes Reinecke <hare@suse.com>
Integrate the option to use an OverlayFS as the root filesystem
into the 90dmsquash-live module for testing purposes.
The rd.live.overlay.overlayfs option allows one to request an
OverlayFS overlay. If a persistent overlay is detected at the
standard LiveOS path, the overlay & type detected will be used.
Tested primarily with transient, in-RAM overlay boots on vfat-
formatted Live USB devices, with persistent overlay directories
on ext4-formatted Live USB devices, and with embedded, persistent
overlay directories on vfat-formatted devices. (Persistent overlay
directories on a vfat-formatted device must be in an embedded
filesystem that supports the creation of trusted.* extended
attributes, and must provide valid d_type in readdir responses.)
The rd.live.overlay.readonly option, which allows a persistent
overlayfs to be mounted read only through a higher level transient
overlay directory, has been implemented through the multiple lower
layers feature of OverlayFS.
The default transient DM overlay size has been adjusted up to 32 GiB.
This change supports comparison of transient Device-mapper vs.
transient OverlayFS overlay performance. A transient DM overlay
is a sparse file in memory, so this setting does not consume more
RAM for legacy applications. It does permit a user to use all of
the available root filesystem storage, and fails gently when it is
consumed, as the available free root filesystem storage on a typical
LiveOS build is only a few GiB. Thus, when booted on other-
than-small RAM systems, the transient DM overlay should not overflow.
OverlayFS offers the potential to use all of the available free RAM
or all of the available free disc storage (on non-vfat-devices)
in its overlay, even beyond the root filesystem available space,
because the OverlayFS root filesystem is a union of directories on
two different partitions.
This patch also cleans up some message spew at shutdown, shortens
the execution path in a couple of places, and uses persistent
DM targets where required.
Documentation is updated for these changes.
Some docs claimed that values in certain config files would be
overwritten, when they would actually be overridden.
Override: a file is not modified but its contents are superseded by
something else. (configurations set in
/etc/dracut.conf.d/*.conf override configurations set in
/etc/dracut.conf)
Overwrite: a file is modified or its contents replaced by an action
(use dracut --force to overwrite the existing initramfs)
Add a systemd generator for root=nbd:.. so that systemd has a correct
sysroot.mount unit.
Use export names instead of port numbers, because port number based
exports are deprecated and were removed.
Add descriptions for the rd.live.overlay.readonly,
rd.live.overlay.size, rd.live.overlay.reset,
rd.live.squashimg, and rd.live.overlay=none options.
Mention the Invalid mark on exhausted overlays.
Clarify the rd.writable.fsimg option.
Repunctuate the rd.live.overlay.thin option description.
rd.net.dhcp.retry=<cnt>
If this option is set, dracut will try to connect via dhcp
<cnt> times before failing. Default is 1.
rd.net.timeout.dhcp=<arg>
If this option is set, dhclient is called with "-timeout <arg>".
rd.net.timeout.iflink=<seconds>
Wait <seconds> until link shows up. Default is 60 seconds.
rd.net.timeout.ifup=<seconds>
Wait <seconds> until link has state "UP". Default is 20 seconds.
rd.net.timeout.route=<seconds>
Wait <seconds> until route shows up. Default is 20 seconds.
rd.net.timeout.ipv6dad=<seconds>
Wait <seconds> until IPv6 DAD is finished. Default is 50 seconds.
rd.net.timeout.ipv6auto=<seconds>
Wait <seconds> until IPv6 automatic addresses are assigned.
Default is 40 seconds.
rd.net.timeout.carrier=<seconds>
Wait <seconds> until carrier is recognized. Default is 5 seconds.
(cherry picked from commit d8ad687e1a)
Lukas Nykryn