91zipl tries to read the filesystem for the /boot/zipl device.
On SLE12, however, the ext2 and ext3 filesystems are handled
by the ext4 module.
And due to bug#886839 no error is registered and booting fails.
So implement a band-aid to translate it into ext4.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Add new module to update the dracut commandline values
during booting with the values found in the file
dracut-cmdline.conf on the device specified by
rd.zipl.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Contrary to the original patch, this one has been modified
to check for /boot/zipl, the location of the first stage kernel
in indirect boot, in order not to install on systems
booting directly via zipl.
Signed-off-by: Daniel Molkentin <daniel.molkentin@suse.com>
When the system boots with EFI, then initrd image is stored
on EFI System Partition. Thus dracut always warn about the
failure to invoke fsfreeze on the partition.
This prevents to run fsfreeze on ESP and suppress the warning.
Add s390 dcssblk driver and introduce rd.dcssblk= to pass mounts
that should get activated at initrd stage.
References: FATE#308263
Signed-off-by: Hannes Reinecke <hare@suse.de>
Allow filesystem modules to install a fs-specific text file with
instructions on what to do when mount fails. This is printed when we go into
an emergency shell.
Signed-off-by: Mark Fasheh <mfasheh@suse.de>
- dracut replaced every instance of "-i" in the cmdline,
even if it was part of a kernel image name, e.g. "vmlinuz-i"
- Fixes boo#908452
Signed-off-by: Fabian Vogt <fvogt@suse.com>
Adjusted to not support "dracut -ifoo bar", as this breaks expected
upstream behavior.
8f5c5 broke the case where BOOT_IMAGE is not set at all.
This code should handle following:
1) BOOT_IMAGE not set
2) BOOT_IMAGE set to something unrelated (s390)
3) BOOT_IMAGE=vmlinuz-4.14.7-300.fc27.x86_64
4) BOOT_IMAGE=/vmlinuz-4.14.7-300.fc27.x86_64
5) BOOT_IMAGE=/boot/vmlinuz-4.14.7-300.fc27.x86_64
6) BOOT_IMAGE=subdir/vmlinuz-4.14.7-300.fc27.x86_64
7) BOOT_IMAGE=/subdir/vmlinuz-4.14.7-300.fc27.x86_64
8) BOOT_IMAGE=/boot/subdir/vmlinuz-4.14.7-300.fc27.x86_64
https://bugzilla.redhat.com/show_bug.cgi?id=1415032
Using the module option 'scsi_mod.scan=manual'
this implements LUN masking by selectively enable only those
devices required for booting.
References: bsc#954600,FATE#319786
Signed-off-by: Hannes Reinecke <hare@suse.de>
Now that we are using persistent network names we can switch
to using the interface names when specifying the fcoe configuration.
With that we can print the fcoe configuration only once.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Occasionally the FCoE connection might be reset after fipvlan was
called, causing the FCoE connection to be dropped and boot to fail.
For these cases we should be adding a timeout entry for the
initqueue to have a failsave mechanism to re-run fipvlan in
these cases.
References: bsc#1052840
Signed-off-by: Hannes Reinecke <hare@suse.com>
bnx2fc doesn't _actually_ need fcoemon, so fipvlan is sufficient
to start the FCoE connection.
And, in fact, fcoemon is started for every interface, causing
subsequent invocations to fail with
fcoemon[1157]: error 98 address already in use
and fcoemon tearing down the connection.
References: bsc#1052840
Signed-off-by: Hannes Reinecke <hare@suse.com>
The 'mode' argument was never referenced in the printf format, causing
invalid rules to be written.
References: bsc#1036323
Signed-off-by: Hannes Reinecke <hare@suse.com>
We should be disabling the FCoE connection (which triggers sending
a LOGO internally) to logout from the target; this resets the target
and will avoid hitting a busy condition during reboots.
References: bsc#994860
Signed-off-by: Hannes Reinecke <hare@suse.com>
fcoemon is well capable of figuring out whether a vlan should
be used, so there's no need to disable the AUTO_VLAN feature.
References: bsc#995019
Signed-off-by: Hannes Reinecke <hare@suse.com>
Harald Hoyer