This is needed since few gpio/pinctrl can be built as modules and are
useful on early boot.
One example is jetson-tx1 where sata and external mmc can work only
after loading pinctrl-max77620 and gpio-max77620 modules.
Having theses kind of drivers bundled into the initramfs will also
avoid some deferred probes.
V2: add pinctrl for all arches
Signed-off-by: Nicolas Chauvet <kwizart@gmail.com>
since kmod-25 keyword "external" was implemented in order to avoid
additional actions(like weak-modules) when kernel was updated, which
makes it more simple while kernels' kabi were compatible.
but if move some special modules such as megaraid_sas, mpt3sas and
so on, to a external path like /opt/modules, these modules will not
be install to initramfs by default, which make the initramfs can't
be used to boot for disk detection failure.
according to kmod's document, you must specify a absolute path with
"external" keyword, so scan the lines in modules.dep that begin with
"/" and install them, to make sure necessary modules in external path
can be installed to initramfs too.
Signed-off-by: Hui Wang <john.wanghui@huawei.com>
Some of the more complex devices now need rpmsg and hwspinlock in the early boot
process to start, and these to the initrd, and pull in usb/misc because
apparently non standard usb hubs are a thing.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
If a hisi_sas storage device is used as / during system install, the
resulting installation will not boot because the hisi_sas driver is not
included in the initramfs.
The Hisilicon storage driver needs to be added to the initramfs image for
aarch64 kernels.
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Cc: dzickus@redhat.com
Cc: dmarlin@redhat.com
Cc: wefu@redhat.com
Cc: harald@redhat.com
This adds the same list of drivers we use for arm platforms for
aarch64 too, also add the DMA drivers there too as they can add
sigficant performance for some storage/usb and often need to be
present when the storage drivers load.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
There's a number of usb controllers that are common yet aren't
contained in the host directory. Include these for generic host.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
The phy and power modules are needed by some of the recent ARM
devices that have appeared like CHIP and some exynos devices.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Contrary to previous intel pinctrl drivers, the cherryview driver can be
and usually is built as a module. However, it sets up the SDIO pinout
so sdhci can make use of the SD card reader, which may subsequently
hold a root file system on a card (bsc#998440).
This will bundle clock drivers into the initramfs on arm
Tested on ti dm8148-t410 where adpll is needed on 4.6+ kernel
This will avoid to rely on (maybe broken) bootloader clocks.
Theses modules are also usually loaded early. Having them bundled into
the initramfs will avoid lot of deferred probes and others delay.
Signed-off-by: Nicolas Chauvet <kwizart@gmail.com>
The sdhci-pci module is currently not being included in the initramfs,
even though other sdhci modules are. This breaks boot on systems that
rely on this driver to access the root filesystem.
Instead of looking for modules that use sdhci_pltfm_init, look for
sdhci_add_host. I checked 3.18 kernel sources, and this change
does not remove any of the previously-matched SDHCI drivers.
It should result in the addition of sdhci-pci, sdhci-s3c, sdhci-spear
and sdhci-acpi.
As reported in https://bugs.mageia.org/show_bug.cgi?id=14799
the xhci module got splitted up in upstream linux merged during
3.18 release cycle:
>From 29e409f0f7613f9fd2235e41f0fa33e48e94544e Mon Sep 17 00:00:00 2001
From: Andrew Bresticker <abrestic@chromium.org>
Date: Fri, 3 Oct 2014 11:35:29 +0300
Subject: xhci: Allow xHCI drivers to be built as separate modules
so we need to adjust 90kernel-modules accordingly.
Signed-off-by: Thomas Backlund <tmb@mageia.org>
The usb_storage, nvme and sdhci_acpi modules are discovered with the
block_module_filter so there's no need to explicitly list them here.
Signed-off-by: <pbrobinson@gmail.com>
The synthetic keyboard of a Gen2 Linux VM doesn't work before the
hyperv_keyboard module is loaded. Without it, we can't cancel the media check
phase if boot with rd.live.check option.
Gen1 Linux VM doesn't have the same issue because the host emulates the legacy
i8042 keyboard for Gen1 VM.
Signed-off-by: Vaughan Cao <vaughan.cao@oracle.com>
Currently the block driver detection for generic initrd doesn't include
the SD/MMC drivers so we fail to boot generic images on any device using
those platforms as boot devices when using a generic initrd. Add logic
to detect those modules. This primarily fixes embedded ARM devices but
also likely intel tablets/dev boards and enterprise hypervisors that
have the ability to boot from SD.
Also the ahci_init_controller misses a number of drivers that use the
libahci_platform module for the init so this fixes some missing achi
moduless too.
Finally it cleans up the ARM storage module hacks that the above now
deals with in a more generic manner.
Signed-off-by: <pbrobinson@gmail.com>
kernel-tegra is now part of the base kernel package, so bits and pieces
ended up modular, and as a result, if you boot off the internal USB, you
drop to a dracut shell with no way of getting to root.
Kairui Song