As the 'multipath' program will be triggered directly from
udev events it will be called before the multipath service
unit has started up. Which means we cannot rely on the
service unit to load the module for us, but we rather
have to do it early before udev is started.
References: bsc#986734
Signed-off-by: Hannes Reinecke <hare@suse.com>
81cio_ignore: handle cio_ignore commandline
References: bnc#874902
Incorporates following on-top patches/fixes:
----------------------------
Subject: 81cio_ignore: skip module if cio_ignore is not active
When cio_ignore is not active we should skip the entire module
during boot; otherwise it'll lead to adverse effects.
References: bnc#882685
----------------------------
Subject: 81cio_ignore: rewrite module
Rewrite cio_ignore module to rely on the dracut commandline
parameter 'rd.cio_accept', which takes a comma-separated list
of CCW IDs. Each of those IDs are being removed from the
list of devices from cio_ignore.
The default values for rd.cio_accept are taken from
/boot/zipl/active_devices.txt.
References: bnc#882685
-----------------------------
Subject: More empty cmdline fixes
This fixes up some more modules which might print out empty
commandline files.
-----------------------------
Subject: Mark scripts as executable
All scripts need to be marked as executable, otherwise dracut
won't be running them.
References: bnc#887010
Signed-off-by: Thomas Renninger <trenn@suse.de>
According to Cathy Zhou <Cathy.Zhou@Oracle.COM>:
"iscsistart is not designed to be working together with iscsid. When an
interface gets the dhcp offer successfully, the iscsiroot script is run
which starts the iscsistart service to establish the iSCSI session. With
the existence of iscsid, the iscsistart service's attempt to setup its
own mgmt ipc fails. Instead, the request to login to the iscsi target
is handled by the mgmt ipc of iscsid. After iscsistart finishes its
login attempt, it eventually sends a stop_event_loop request to stop
the mgmt process. As the result, it terminates iscsid."
So, iscsid is kicked out again.
Additionally iscsistart-flocked is used to make sure iscsistart is not
run in parallel.
91zipl tries to read the filesystem for the /boot/zipl device.
On SLE12, however, the ext2 and ext3 filesystems are handled
by the ext4 module.
And due to bug#886839 no error is registered and booting fails.
So implement a band-aid to translate it into ext4.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Add new module to update the dracut commandline values
during booting with the values found in the file
dracut-cmdline.conf on the device specified by
rd.zipl.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Contrary to the original patch, this one has been modified
to check for /boot/zipl, the location of the first stage kernel
in indirect boot, in order not to install on systems
booting directly via zipl.
Signed-off-by: Daniel Molkentin <daniel.molkentin@suse.com>
Add s390 dcssblk driver and introduce rd.dcssblk= to pass mounts
that should get activated at initrd stage.
References: FATE#308263
Signed-off-by: Hannes Reinecke <hare@suse.de>
Allow filesystem modules to install a fs-specific text file with
instructions on what to do when mount fails. This is printed when we go into
an emergency shell.
Signed-off-by: Mark Fasheh <mfasheh@suse.de>
8f5c5 broke the case where BOOT_IMAGE is not set at all.
This code should handle following:
1) BOOT_IMAGE not set
2) BOOT_IMAGE set to something unrelated (s390)
3) BOOT_IMAGE=vmlinuz-4.14.7-300.fc27.x86_64
4) BOOT_IMAGE=/vmlinuz-4.14.7-300.fc27.x86_64
5) BOOT_IMAGE=/boot/vmlinuz-4.14.7-300.fc27.x86_64
6) BOOT_IMAGE=subdir/vmlinuz-4.14.7-300.fc27.x86_64
7) BOOT_IMAGE=/subdir/vmlinuz-4.14.7-300.fc27.x86_64
8) BOOT_IMAGE=/boot/subdir/vmlinuz-4.14.7-300.fc27.x86_64
https://bugzilla.redhat.com/show_bug.cgi?id=1415032
Using the module option 'scsi_mod.scan=manual'
this implements LUN masking by selectively enable only those
devices required for booting.
References: bsc#954600,FATE#319786
Signed-off-by: Hannes Reinecke <hare@suse.de>
Now that we are using persistent network names we can switch
to using the interface names when specifying the fcoe configuration.
With that we can print the fcoe configuration only once.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Occasionally the FCoE connection might be reset after fipvlan was
called, causing the FCoE connection to be dropped and boot to fail.
For these cases we should be adding a timeout entry for the
initqueue to have a failsave mechanism to re-run fipvlan in
these cases.
References: bsc#1052840
Signed-off-by: Hannes Reinecke <hare@suse.com>
bnx2fc doesn't _actually_ need fcoemon, so fipvlan is sufficient
to start the FCoE connection.
And, in fact, fcoemon is started for every interface, causing
subsequent invocations to fail with
fcoemon[1157]: error 98 address already in use
and fcoemon tearing down the connection.
References: bsc#1052840
Signed-off-by: Hannes Reinecke <hare@suse.com>
The 'mode' argument was never referenced in the printf format, causing
invalid rules to be written.
References: bsc#1036323
Signed-off-by: Hannes Reinecke <hare@suse.com>
We should be disabling the FCoE connection (which triggers sending
a LOGO internally) to logout from the target; this resets the target
and will avoid hitting a busy condition during reboots.
References: bsc#994860
Signed-off-by: Hannes Reinecke <hare@suse.com>
fcoemon is well capable of figuring out whether a vlan should
be used, so there's no need to disable the AUTO_VLAN feature.
References: bsc#995019
Signed-off-by: Hannes Reinecke <hare@suse.com>
Old code did not work for two most common use-cases.
On most machines BOOT_IMAGE is set to something like
/vmlinuz-4.11.3-202.fc25.x86_64. So if we just add prefix "/boot/."
it won't work. Also on machines without /boot on separate partition
BOOT_IMAGE already has the /boot/ prefix (/boot/vmlinuz-3.10.0-799.el7.x86_64).
So let's strip it in such case.
https://bugzilla.redhat.com/show_bug.cgi?id=1415032
The needle argument in this specific case is a pattern, which cannot be
matched by the "literal" string matcher strstr.
This can result in fsck calls like:
e2fsck -a -y /dev/sda1
Which will then exit with an error like:
e2fsck: Only one of the options -p/-a, -n or -y may be specified.
Hence, it is necessary to use the strglobin function to correctly match
the pattern.
The "host" command may also print something else than
"asdf.local.lan has address 1.2.3.4", like:
"rootserver.local.net is an alias for rainbow.local.net.".
So "head -n1" is not enough.
Fixes boo#955592
References: boo#965477
fcoe-uefi gets included by default on EFI systems,
as it does not do the same check that fcoe does,
therefore needlessly pulling in network modules.
This patch copies the check from fcoe to fcoe-uefi.
We're now parsing the 'rd.dasd' parameter from 95dasd_rules, so
setting the 'dasd_mod' module parameter should be dropped here.
Signed-off-by: Hannes Reinecke <hare@suse.de>
There is no point trying to delete partitions; dmraid works
happily even with them. On the contrary trying to delete partitions
can even be harmful when eg dmraid should _not_ be started.
References: bsc#998860
Signed-off-by: Hannes Reinecke <hare@suse.com>
DM devices might be located on top of MD devices, so we need to
call the DM shutdown script before MD shutdown. The exception
here are multipath devices, which are below MD devices.
So skip removing multipath devices here to avoid spurious errors.
References: bsc#994860
Signed-off-by: Hannes Reinecke <hare@suse.com>
When calling the shutdown script we need to take care of traversing
the device-mapper tables, otherwise we might end up trying to remove
a device-mapper device which still has another one stacked on top
and the removal will fail.
References: bsc#994860
Signed-off-by: Hannes Reinecke <hare@suse.com>
local-fs-pre.target serves as a separator between the code for
detecting block devices and systemd's fsck/mount logic. This
patch ensures that multipathd is started before local-fs-pre.target
in the initrd. By adding a "Wants=" line for local-fs-pre.target,
it makes sure that this target is started at all.
References: bsc#1006118
Signed-off-by: Martin Wilck <mwilck@suse.de>
===================================================================
SLES11 provided a kernel commandline option 'multipath=off',
so dracut should be parsing the option, too.
References: bsc#1001691
Signed-off-by: Hannes Reinecke <hare@suse.com>
As the device-mapper module is removing all device-mapper tables
during shutdown we need to make sure to disable queuing on the
multipath devices; otherwise there might still be I/O pending
and the removal will fail.
References: bsc#994860
Signed-off-by: Hannes Reinecke <hare@suse.com>
We need to wait until udev has processed all events, otherwise we'll
risk of misdetecting devices. This might cause a temporary interruption
during which multipath removes a device-mapper device, which then
causes a booting failure.
References: bsc#986734
Signed-off-by: Hannes Reinecke <hare@suse.com>
References: bsc#930019
If rootfs is on multipath, but platform does not have an /etc/multipath.conf
file which is not urgently needed, they system will not boot, due to:
multipathd is not started and rootfs and swap are not found:
systemctl status multipathd.service
* multipathd.service - Device-Mapper Multipath Device Controller
Loaded: loaded (/usr/lib/systemd/system/multipathd.service; disabled; vendor preset: enabled)
Active: inactive (dead)
Condition: start condition failed at Thu 2015-05-07 11:49:11 CEST; 7min ago
ConditionPathExists=/etc/multipath.conf was not met
and exit to dracut shell.
With hostonly enabled, only modules that are currently
loaded are included in the initrd. Modules which are
explicitly listed in modules-load.d do not need to
be filtered that way. Fix for boo#962224.
FCoE can run in Fabric (ie FCF) or VN2VN mode, so we should allowing
to set this parameter from the commandline, too.
Signed-off-by: Hannes Reinecke <hare@suse.com>
When lldpad is not running, any calls to 'dcbtool' will be printing
out a warning. As it perfectly legit to have FCoE running without
DCB we should not be printing out the error.
Signed-off-by: Hannes Reinecke <hare@suse.com>
If the installation already has a FCoE configuration we should
not attempt to overwrite it but rather use the pre-defined
configuration.
References: bsc#993861
Signed-off-by: Hannes Reinecke <hare@suse.com>
Check first if we're running off an bnx2x device and start FCoE on it
via fipvlan, then go the normal/Intel way of starting DCB.
Also the SUSE version of fcoemon needs the yes parameter for the
--syslog option
References: bsc#982588
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.com>
The recently upstreamed virtualbox video driver (vboxvideo) is shipped
in the staging directory. We need to probe it before Xorg is loaded to
avoid a corrupted X.
In general it is a good practice to look also in the staging directory
for DRM drivers.
Signed-off-by: Carlo Caione <carlo@endlessm.com>
This was removed from systemd almost two years ago in
c550f7a9b89d017215af084288bc44f736f774fe, so dracut should drop support
as well.
Reference: bsc#1067279
Although no device uses multipath, the module checks
for presence of the multipath binary first, printing a
warning if not present. This patch fixes the wrong ordering.
Fix issue #279 supercede PR #299
Fix bug https://issues.openmandriva.org/show_bug.cgi?id=2219
Replace Bashisms in the boot message for a missing overlay.
Verify presence of plymouth before calling it.
(Rework of commit f1b65e92af5e3f9df79f99e55d5aa936c9bca940.)
Previously, dracut would only copy the first one found. However,
with legacy maps for some locales around, there is a chance we
pick the wrong one. Pick all matching keymaps instead
Reference: boo#1065058
If no iscsi session information can be retrieved from the firmware
then skip the iscsi attachment and allow the boot process to continue.
Ensure the timeout scripts don't hit their timeout waiting for
/tmp/iscsistarted-firmware to be created.
This will allow a common image to be used for servers with both a
local and iscsi root with rd.iscsi.firmware set.
Some of the more complex devices now need rpmsg and hwspinlock in the early boot
process to start, and these to the initrd, and pull in usb/misc because
apparently non standard usb hubs are a thing.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Type=oneshot, as currently set in dracut's emergency service file,
causes an awkward situation if emergency mode is entered e.g. because
of a root device timeout, and the root device appears later because it
just has taken longer than the timeout. In that situation, my
expectation (backed by past positive experience) is that the user should
be able to simply exit the emergency shell and resume normal boot.
:/# systemctl status sysroot.mount
● sysroot.mount - /sysroot
Loaded: loaded (/proc/cmdline; bad; vendor preset: enabled)
Active: active (mounted) since Mon 2017-10-09 14:32:15 CEST; 16s ago
Where: /sysroot
What: /dev/mapper/3600601600a30200024fbbaf3f500e411-part5
Docs: man:fstab(5)
man:systemd-fstab-generator(8)
Process: 1873 ExecMount=/usr/bin/mount /dev/disk/by-uuid/63751805-6abc-46a3-a66f-427920dece4d /sysroot -o ro (code=exited, status=0/SUCCESS)
Tasks: 0 (limit: 512)
:/# systemctl list-jobs
JOB UNIT TYPE STATE
56 emergency.target start waiting
57 emergency.service start running
2 jobs listed.
:/# exit
logout
Failed to start default.target: Transaction is destructive.
(system keeps idling from this point on, user has no chance to
do anything).
This results from the combination of two effects:
1) initrd-root-fs.target sets "OnFailureJobMode=replace-irreversibly",
2) emergency.service's Type=oneshot causes the start jobs for both
emergency.service and emergency.target to persist while the user is in
the emergency shell.
When the shell is exited, systemd tries to isolate "initrd.target"
again, but this fails with "the transaction is destructive" error
because of the still pending jobs.
This patch fixes this by changing the Type of "emergency.service" from
"oneshot" to "idle".
JobRunningTimeoutSec now affects how long can start jobs for device
units stay in the "running" state. Disabling default job timeout via
JobTimeoutSec=0 doesn't disable running state timeout. We need to set
running state timeout as well.
Note that doing this the other way around has effect on generic timeout,
i.e. disabling running state timeout disables generic timeout. But doing
it this way we would create implicit dependency on fairly new
systemd-234. However, by setting both options we don't create dependency
on specific systemd version.
A LUKS root volume with a detached header on a device without partitioning will not have a UUID and will not have an attribute ENV{ID_FS_TYPE}=="crypto_LUKS".
Therefore, several areas need to be addressed: identification of the LUKS device, inclusion of entries within crypttab, and provision of the detached header file.
- Added support for an option (4th column: "force") in /etc/crypttab to force the inclusion of the entry in the initramfs version (avoiding the fs type test).
- Added support for an option (4th column: "header=/path/to/file") in /etc/crypttab to provide a path to a detached header file embedded within the initramfs.
- Added ID and PARTUUID support to the device (2nd column) in /etc/crypttab (complementing the existing UUID functionality).
- Added cmdline support to indicate LUKS device ("rd.luks.serial=") that refers to the attribute ENV{ID_SERIAL_SHORT}.
Tested successfully on Void Linux (x86_64 musl) (no systemd) with a LUKS root volume accessed with a keyfile and using a detached header.
Not tested on systemd, or on a LUKS root volume with a passphrase rather than a keyfile.
Some Combined Network Adapters(CNAs) implement DCB protocol
in firmware, it is recommended that do not run software-based
DCB or LLDP on CNAs that implement DCB, but we have to start
the lldpad service anyway(there might be other software DCB).
If the network interface provides hardware DCB/DCBX capabilities,
the field DCB_REQUIRED in "/etc/fcoe/cfg-xxx" is expected to
be set to "no".
We met an issue on "QLogic BCM57810" with DCB firmware support,
and found dracut still generated "fcoe=<mac>:dcb" which caused
kdump boot failure when using that fcoe dump target.
This patch parses /etc/fcoe/cfg-xxx to detect DCB_REQUIRED="no",
and force "nodcb" if it is the case.
Also improved some coding style in passing.
Signed-off-by: Xunlei Pang <xlpang@redhat.com>
Prior to this commit, the MTU setting was applied to a bond slave
interface. In older versions of the Linux kernel, this setting
propagated to the bond master and the other bond slaves associated with
the master. In recent versions of the kernel (observed in Linux 4.12),
increasing the MTU of a slave does not automatically increase the MTU of
the master. This allows for more flexibility but requires the MTU of
the master to be changed manually.
Ideally, the MTU setting should be applied to the bond master and the
setting will propagate to the bond slaves, since the slaves are required
to have a MTU that is greater than or equal to the bond master.
systemd sets /proc/sys/kernel/core_pattern to use systemd-coredump.
However, systemd-coredump is missing from initrd, making dumping
the core in initrd impossible by default.
Reference: bsc#1054809
In case of "--no-hostonly-default-device", we do not need
the root device, thus add this check.
Also fixed the stale "root_dev" export.
Signed-off-by: Xunlei Pang <xlpang@redhat.com>
Hannes Reinecke