The "host" command may also print something else than
"asdf.local.lan has address 1.2.3.4", like:
"rootserver.local.net is an alias for rainbow.local.net.".
So "head -n1" is not enough.
Fixes boo#955592
References: boo#965477
fcoe-uefi gets included by default on EFI systems,
as it does not do the same check that fcoe does,
therefore needlessly pulling in network modules.
This patch copies the check from fcoe to fcoe-uefi.
We're now parsing the 'rd.dasd' parameter from 95dasd_rules, so
setting the 'dasd_mod' module parameter should be dropped here.
Signed-off-by: Hannes Reinecke <hare@suse.de>
There is no point trying to delete partitions; dmraid works
happily even with them. On the contrary trying to delete partitions
can even be harmful when eg dmraid should _not_ be started.
References: bsc#998860
Signed-off-by: Hannes Reinecke <hare@suse.com>
DM devices might be located on top of MD devices, so we need to
call the DM shutdown script before MD shutdown. The exception
here are multipath devices, which are below MD devices.
So skip removing multipath devices here to avoid spurious errors.
References: bsc#994860
Signed-off-by: Hannes Reinecke <hare@suse.com>
When calling the shutdown script we need to take care of traversing
the device-mapper tables, otherwise we might end up trying to remove
a device-mapper device which still has another one stacked on top
and the removal will fail.
References: bsc#994860
Signed-off-by: Hannes Reinecke <hare@suse.com>
local-fs-pre.target serves as a separator between the code for
detecting block devices and systemd's fsck/mount logic. This
patch ensures that multipathd is started before local-fs-pre.target
in the initrd. By adding a "Wants=" line for local-fs-pre.target,
it makes sure that this target is started at all.
References: bsc#1006118
Signed-off-by: Martin Wilck <mwilck@suse.de>
===================================================================
SLES11 provided a kernel commandline option 'multipath=off',
so dracut should be parsing the option, too.
References: bsc#1001691
Signed-off-by: Hannes Reinecke <hare@suse.com>
As the device-mapper module is removing all device-mapper tables
during shutdown we need to make sure to disable queuing on the
multipath devices; otherwise there might still be I/O pending
and the removal will fail.
References: bsc#994860
Signed-off-by: Hannes Reinecke <hare@suse.com>
We need to wait until udev has processed all events, otherwise we'll
risk of misdetecting devices. This might cause a temporary interruption
during which multipath removes a device-mapper device, which then
causes a booting failure.
References: bsc#986734
Signed-off-by: Hannes Reinecke <hare@suse.com>
References: bsc#930019
If rootfs is on multipath, but platform does not have an /etc/multipath.conf
file which is not urgently needed, they system will not boot, due to:
multipathd is not started and rootfs and swap are not found:
systemctl status multipathd.service
* multipathd.service - Device-Mapper Multipath Device Controller
Loaded: loaded (/usr/lib/systemd/system/multipathd.service; disabled; vendor preset: enabled)
Active: inactive (dead)
Condition: start condition failed at Thu 2015-05-07 11:49:11 CEST; 7min ago
ConditionPathExists=/etc/multipath.conf was not met
and exit to dracut shell.
With hostonly enabled, only modules that are currently
loaded are included in the initrd. Modules which are
explicitly listed in modules-load.d do not need to
be filtered that way. Fix for boo#962224.
FCoE can run in Fabric (ie FCF) or VN2VN mode, so we should allowing
to set this parameter from the commandline, too.
Signed-off-by: Hannes Reinecke <hare@suse.com>
When lldpad is not running, any calls to 'dcbtool' will be printing
out a warning. As it perfectly legit to have FCoE running without
DCB we should not be printing out the error.
Signed-off-by: Hannes Reinecke <hare@suse.com>
If the installation already has a FCoE configuration we should
not attempt to overwrite it but rather use the pre-defined
configuration.
References: bsc#993861
Signed-off-by: Hannes Reinecke <hare@suse.com>
Check first if we're running off an bnx2x device and start FCoE on it
via fipvlan, then go the normal/Intel way of starting DCB.
Also the SUSE version of fcoemon needs the yes parameter for the
--syslog option
References: bsc#982588
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.com>
The recently upstreamed virtualbox video driver (vboxvideo) is shipped
in the staging directory. We need to probe it before Xorg is loaded to
avoid a corrupted X.
In general it is a good practice to look also in the staging directory
for DRM drivers.
Signed-off-by: Carlo Caione <carlo@endlessm.com>
This was removed from systemd almost two years ago in
c550f7a9b89d017215af084288bc44f736f774fe, so dracut should drop support
as well.
Reference: bsc#1067279
The caller of "for_each_host_xx func" needs to tell three cases:
func success/ fail / not be called.
E.g, in kdump case, host_devs can be empty, and we want to know it.
Signed-off-by: Pingfan Liu <piliu@redhat.com>
Although no device uses multipath, the module checks
for presence of the multipath binary first, printing a
warning if not present. This patch fixes the wrong ordering.
Fix issue #279 supercede PR #299
Fix bug https://issues.openmandriva.org/show_bug.cgi?id=2219
Replace Bashisms in the boot message for a missing overlay.
Verify presence of plymouth before calling it.
(Rework of commit f1b65e92af5e3f9df79f99e55d5aa936c9bca940.)
Harald Hoyer