We tell dhclient to name 121 option "classless-routes",
but in dhclient-script we parse classless_static_routes.
So either have to change the configuration or the script.
And since dhclient uses by default classless_static_routes,
let's change the configuration
hardcoding the wwid of the drives in the initramfs causes problems
when the drives are cloned to a system with the same hardware, but
different disk wwid's
https://bugzilla.redhat.com/show_bug.cgi?id=1457311
Support booting from USB media with NTFS filesystem (optionally),
which removes the FAT32 related 4 GB file size limit for LiveOS/
squashfs.img (and any other file on the same USB media).
On s390 BOOT_IMAGE only denotes the number of the boot record that
was selected in the bootloader and not the path to the kernel image.
Also only bail out, if the kernel hmac checking relies on that path.
blkid is not available when this function is called, so block_uuid.map is put into
the initrd, mapping block devices from /etc/crypttab to UUIDs.
This fixes a bug where udev rules were created by mistake as crypttab_contains()
returned false for devices specified by path in /etc/crypttab which resulted in
error messages during boot.
Signed-off-by: Julian Wolf <juwolf@suse.de>
Previously our dhclient-script expected that $new_classless_static_routes
will have all values separated by a whitespace. But at least on F25
dhclient will put there the destination descriptor in the same format
as it is used by ISC dhcp-server.
For example:
new_classless_static_routes=32.10.198.122.47 192.168.78.4
while our current code expects
new_classless_static_routes=32 10 198 122 47 192 168 78 4
So let's just accept both of these formats by adding "." to IFS.
For details plesse see https://tools.ietf.org/html/rfc3442
"Classless Route Option Format"
When NPIV is enabled and the allow_lun_scan parameter is set to 'Y'
the HBA will initiate a LUN scan automatically, so there is no need
to specify the WWPN and LUN number manually.
References: bsc#964456
Signed-off-by: Hannes Reinecke <hare@suse.com>
module_setup.sh has a typo preventing it from saving the correct
dracut commandline.
References: bnc#887582
Signed-off-by: Hannes Reinecke <hare@suse.de>
For creating dynamic udev rules parse-dasd.sh look for the device
type in sysfs, which of course does not exist if cio_ignore is
active. So first enable the device before checking.
Signed-off-by: Hannes Reinecke <hare@suse.de>
'for_each_host_dev_and_slaves' would stop at the first found
device, so the cmdline() call would never list all required
devices. Use 'for_each_host_dev_and_slaves_all' instead and
filter out duplicates.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Setting and unsetting the IFS variable is tricky. To be on the
safe side we should always reset the IFS variable to its original
value after parsing.
Signed-off-by: Hannes Reinecke <hare@suse.de>
For creating dynamic udev rules parse-dasd.sh look for the device
type in sysfs, which of course does not exist if cio_ignore is
active. So first enable the device before checking.
Signed-off-by: Hannes Reinecke <hare@suse.de>
'for_each_host_dev_and_slaves' would stop at the first found
device, so the cmdline() call would never list all required
devices. Use 'for_each_host_dev_and_slaves_all' instead and
filter out duplicates.
Signed-off-by: Hannes Reinecke <hare@suse.de>
When a DASD is found to be required for the rootfs we should
be printing out a 'rd.dasd' commandline parameter. This not
only enables us to correctly enable the device with cio_ignore,
we can also inspect the resulting initrd to figure out which
devices are required to mount the rootfs.
Signed-off-by: Hannes Reinecke <hare@suse.de>
There were some errors when rd.dasd parsing, resulting in the
device never to be activated. And we should check for
cio_ignore even if a udev rules has been found.
Signed-off-by: Hannes Reinecke <hare@suse.de>
When converting 'rd.zfcp' and 'rd.dasd' into udev rules we
need to make sure the enable those device ids via cio_ignore,
otherwise the rules might never be called.
Signed-off-by: Hannes Reinecke <hare@suse.de>
With the new s390x configuration tool the naming of the udev
rules files have changed. So add these to the existing ones
to be compatible with existing and new installations.
References: bnc#856585
Signed-off-by: Hannes Reinecke <hare@suse.de>
When converting 'rd.zfcp' and 'rd.dasd' into udev rules we
need to make sure the enable those device ids via cio_ignore,
otherwise the rules might never be called.
Signed-off-by: Hannes Reinecke <hare@suse.de>
This used to work only when specified via the command line
or if systemd was not being used. However, the exisistence of
20_force_driver.conf also requires dracut-pre-udev.service
to be run.
Reference: bsc#986216
removed copy&paste artifact "modify_routes add"
there is no modify_routes() function, and we simply want the output
of the parse function.
(cherry picked from commit 33710dfbfc)
Harald Hoyer