For cmdline argument with numeric value, add a new function getargnum
It will get proper value with default value as $1, min value as $2,
max value as $3, and param name as $4. valid result will be echo to stdout.
for nul or value not valid it will just echo the default value.
Note: The values should be >=0
[v1->v2]: add arg <minval>
[v2->v3]: do not use bash string match =~
Signed-off-by: Dave Young <dyoung@redhat.com>
linkup is a wrapper function for waiting interface ready and up.
change to use linkup as what we do in ifup script.
Signed-off-by: Dave Young <dyoung@redhat.com>
This also changes the command line switch to be --add-device and the
config directive is set to add_device. This was chosen as device= in the
config file seems too generic and not quite as consistent with other
directives (i.e. drivers/add_drivers)
The --device command line is still supported but it should be considered
deprecated in favour of --add-device.
In case that configuration file did not include name of team device,
teamd would not start. Fix this by adding "-t" parameter.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
In case long delay of network driver initqueue will exit before net dev is
ready. We have no chance to setup it then.
For dhcp, when we finish the setup there will be a setup_net_<dev>.ok. Doing
same for static ip case. Also add a check to initqueue when we generate udev
rules to ensure it's early enough.
[v1->v2]: only wait for bootdev or it's possible to cause boot fail for
waiting for non-bootdev. For example bond0->eth0, set bond0 as bootdev and
dhcp, we only need to wait bond0 setup ok.
Signed-off-by: Dave Young <dyoung@redhat.com>
In case BOOTIF is not set and IFACES are not set in bonding/vlan/bridge code,
net-genrule.sh will fall to bring up all net interfaces.
Here add a failsafe option to read IFACES from /tmp/net.ifaces
[v1->v2]: move IFACES reading from net.ifaces after bonding/vlan/bridge info
code chunks.
[v2->v3]: [ -n "$IFACES" ] should be [ -z "$IFACES" ]
Signed-off-by: Dave Young <dyoung@redhat.com>
Some network driver will take long time to initialize. We have an example
in a HP machine which take about one minute for this. The callback such as
"ip link set <dev> up" will fail, afterwards setup for network will also
fail.
Fix this by add a new function wait_for_if_link, wait the link ready before
use it.
Signed-off-by: Dave Young <dyoung@redhat.com>
set link up usually include two steps, ip link set <dev> up and
wait_for_if_up <dev>. Now do these two steps in one function linkup.
Later patch will add other code into it.
Signed-off-by: Dave Young <dyoung@redhat.com>
V2: merge patch 2/2
fix active-backup mode by adding slaves one by one
sync with the latest teamd
improve the comments
wait for team ports to come up
install /etc/libnl/classid too
This patch adds the initial support for team device [1].
A new cmdline team= is introduced for it.
Note, currently we don't support stacked devices
on/under team, it is tricky and can be added on request.
1. http://www.libteam.org/
Cc: Harald Hoyer <harald@redhat.com>
Cc: Dave Young <dyoung@redhat.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Cong Wang <amwang@redhat.com>
Starting with commit 24a38bc1cb dracut
uses udev builtins but still depends on >=udev-166 in dracut.spec. This
patch makes dracut work with older udev again.
All credits go to Alexander Tsoy <alexander@tsoy.me>; see
https://bugs.gentoo.org/show_bug.cgi?id=437700
This bug was reported as http://bugzilla.redhat.com/873220#c2
As the /etc/modprobe.d isn't created in the boot process
nor bundled within the initramfs, the initramfsblacklist.conf
cannot be created.
Instead, the /usr/lib/modprobe.d directory is available and using it
will restore the blacklist behavior.
Kdump module will need the drm and kms kernel modules so user can see the
emergency shell at least.
Fix this by split 50plymouth module to 50drm and 50plymouth. Moving the
installkernel part to 50drm so user can use drm directly without adding
extra plymouth utils.
Signed-off-by: Dave Young <dyoung@redhat.com>
Tested-by: Chao Wang <chaowang@redhat.com>
1) strstr " $discarduuids " did not remove the optional
'luks-' prefix from the argument as the documentation says.
2) The lookup seems backwards. $luksdev ($luks in the other code copy)
is the full uuid and thus one should check whether the user-supplied
argument (short form) is contained therein, not the other way around.
Before this commit, the only way to trigger allow-discards was to
specify the full uuid without the 'luks-' prefix.
Commit a0be1ed removes some lines from do_static() and do_ipv6auto().
When $hostname is empty, do_static() and do_ipv6auto() will return 1
and fails to run setup_net at the last of ifup.sh
Signed-off-by: WANG Chao <chaowang@redhat.com>
Dave Young