When in hostonly mode, 95fcoe module will still be installed even there
is no FCoE hostonly device. So use the new block_is_fcoe helper to check
for hostonly device in hostonly mode, avoid installing unneccessary module.
Signed-off-by: Kairui Song <kasong@redhat.com>
If fcoe module is loaded, the initramfs will always try load libfcoe
and bnx2fc, so also ensure they are installed if needed.
Signed-off-by: Kairui Song <kasong@redhat.com>
Library file modules.d/99base/dracut-lib.sh contains initialization code
that makes sure certain directories and links are created when a system
runs from the produced initramfs. This file is normally sourced only
from initramfs scripts. However, modules.d/99base/module-setup.sh
includes it also when an initramfs image is being created to gain access
to some of the functions in this library. This can result in creating
unexpected directories and links on the current root file system when
the dracut command is executed.
For instance, during a system installation when dracut is invoked to
create an initial initramfs, the target sysroot might not contain
directory /run/initramfs but have /var/log. This situation results in
the code in modules.d/99base/dracut-lib.sh creating an unexpected link
/var/log/log that points to /run/initramfs/log. This link is then also
present on the installed system.
The patch fixes the problem by skipping the described logic in
modules.d/99base/dracut-lib.sh when the PREFIX variable is non-empty
which indicates that a target initramfs is being prepared. The variable
is set by modules.d/99base/module-setup.sh prior to including
dracut-lib.sh.
When LDFLAGS contains ``-Wl,--as-needed``, the FTS library will be
ignored if it is specified before the .c source.
Signed-off-by: A. Wilcox <AWilcox@Wilcox-Tech.com>
Fixes: 62f27ee6f1 ("configure: find cflags and libs for fts on musl")
dracut builds today are fairly verbose to start, but on top of
that many of the messages tend to liberally use the
exclamation point `!` which calls attention to them.
I see these a lot when looking at rpm-ostree build logs
and it'd be nicer if we were quiet when there wasn't
an actual problem.
In this specific case, if the builder is explicitly adding
`--omit=foo`, there's no reason for us to say:
`dracut: dracut module 'foo' will not be installed, because it's in the list to be omitted!`
We already print the command line to start, so the information
is there.
Demote this message to debug.
Sometimes, systems have more elaborate backends in nsswitch.conf,
the complexity of which we do not want in the initrd. SUSE systems
with atomic for instance, where those files may also reside in /usr/etc.
With this change, the unavaiable nsswitch.conf backends will be silently
ignored, and we still end up with all the information we need.
Reference: boo#1165366
dracutinstall picks up interpreters and includes bash despite
the users' wishes or expectations, as modules should not require
bashisms at runtime.
Fixes#951
This should've been part of #964. As mentioned there, the
`initrd-cryptsetup.target` approach was reverted in the end, and we went
back to relying in `remote-cryptsetup.target`:
https://github.com/systemd/systemd/pull/17467
So we do need to ship the enablement symlink for it.
For strict hostonly mode, only install currently loaded modules instead
of a bunch of driver that may not be needed.
Signed-off-by: Kairui Song <kasong@redhat.com>
Use udevadm to detect the required kernel modules to load a given
device. udevadm will follow the device chain, help detect all required
parent device drivers as well.
Signed-off-by: Kairui Song <kasong@redhat.com>
check_block_and_slaves_all $func $dev should return 0, if $func return 0
for any checked device. Currently if any device don't have any sub
device, 1 is returned instead.
So remove the sub device checking statement. Also remove the same
statement in check_block_and_slaves, the "[[ -f $_x/dev ]]" in the for
loop is enought to ensure sub device exists.
Signed-off-by: Kairui Song <kasong@redhat.com>
Currently when network is enabled, dracut will install all network
drivers that are currently loaded, but some time only one NIC is needed
for the initramfs.
So for strict hostonly mode, add a --hostonly-nics option, user can
provide a list of NICs to be enabled, and only needed drivers for
specifed NICs will be installed so save space.
Signed-off-by: Kairui Song <kasong@redhat.com>
It's like check_kernel_config, help to check if a kernel module is
enabled (cover built-in or compiled module case).
Signed-off-by: Kairui Song <kasong@redhat.com>
This was added in https://github.com/systemd/systemd/pull/17149 and is
the designated cryptsetup target for all encrypted volumes that need to
be opened in the initrd.
So it effectively replaces `cryptsetup.target` and
`remote-cryptsetup.target` there. I've removed the latter since it was
added recently (by me) in #930, but kept `cryptsetup.target` since we've
been shipping it for a long time now.
With commit 3c8c807, /run/initramfs/isoscan and /run/initramfs/live
mountpoints are unmounted upon rd.live.ram boots. Save a link to
the iso-scan device in /run/initramfs/isoscandev to easily remount
the source, if desired.
This is a plain and simple hack around dependency issues between dracut
and systemd.
When using Tang-pinned LUKS root devices, we want to rely on
`systemd-cryptsetup@.service` to unlock it. However, that service only
runs `After=remote-fs-pre.target`, while `dracut-initqueue.service` has
`Before=remote-fs-pre.target` (which makes sense because we don't want
to attempt networked root devices before networking is up).
However, the rootfs-generator here wants to make sure that the root
device exists *before* exiting the initqueue via an initqueue/finished
"devexists" hook. This will never work though because by design
`systemd-cryptsetup@.service`, which unlocks the root device, won't run
until after we exit.
So we have a dependency cycle:
initqueue -> devexists hook -> root device ->
systemd-cryptsetup@.service -> remote-fs-pre.target -> initqueue
There's no clean way to break this. The root issue is that there's no
way right now to split sequencing of systemd services across the
initqueue/online and initqueue/finished events because it's all bundled
in a single service. (The deeper root issue of course is that we have
two init systems. :) ).
Here we do a tactical fix: if there's a `systemd-cryptsetup@.service`
instance, let's assume it's for the root device and skip waiting for it
to show up if it depends on `remote-fs-pre.target`.
dracut feeds whatever it receives in password field of
crypttab(5) to `cryptsetup -d`, treating them as plain-text key file.
Meanwhile, dracut treats the key file from `rd.luks.key` differently,
by have some special rules to decrypt those key files that has extension of
`gpg` and `img`.
Let's begin to treat them the same.
This is a backward-incompatible change for those people
that uses plain-text key-file that has extension of `gpg` and `img`.
However, those setup is questionable to begin with.
In the case of the s805x the drivers/hwmon directory contains the
scpi_hwmon kernel module.
On a running system, lsmod would output the following dependencies:
arm_scpi 24576 2 clk_scpi,scpi_hwmon
It means that if the clock driver is bundled in the initramfs it will
bring arm_scpi. But if scpi_hwmon is missing the scpi will be incomplete
and it can lead to crashes.
When the hwmon is bundled, no crash occurs
Signed-off-by: Nicolas Chauvet <kwizart@gmail.com>
Some filesystem (e.g. ZFS, and btrfs subvolumes) don't use block
devices. Should they be mounted as `/`, `find_root_block_device`
yields nothing, hence dracut will append this problematic argument
to kernel cmdline:
root=/dev/block
On a machine that employ root ZFS on LUKS, which was setup with
an OpenPGP-encrypted key file, this argument renders that machine
unbootable. Remove that `root=/dev/block` manually could boot the
machine.
Let check if that device is a block device before write down `root`
argument. This is consistent with the check for block device in
`find_block_device`.
Signed-off-by: Đoàn Trần Công Danh <congdanhqx@gmail.com>
D-Bus doesn't run in the initrd, so our usual trick of activating
custom systemd services from udev doesn't work.
So add a rule to create initqueue entries for each possible
connection.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Always add the nvmf.discover parameters to /etc/nvme/discovery
when parsing the dracut commandline, and rely on NVMe autodiscovery
when no parameters are given.
And modify the syntax to use a comma ',' as a separator for nvmf.discover
as the semicolon ':' is already used for the FC-NVMe transport address format.
Signed-off-by: Hannes Reinecke <hare@suse.de>
This was introduced with 6dafdda4a6, but
is actually caused by the fact that modules that have already been
installed cause dracut_install() to return without adding the module
to the hashmap. This can happen if an earlier-run dracut module chose
to install the same module. Now modprobe statements like:
softdep usb_storage post: uas
softdep uas pre: usb_storage
(which look weird, but are perfectly valid), cause
dracut_install() to enter an infinite recursion if and only if
at least one of the files has previously been installed by another
module.
Fix this by also adding already installed modules to the hashmap.
If there are any nonexistent libraries listed in /etc/ld.so.preload, ldd
prints error messages like:
ERROR: ld.so: object '/usr/lib64/libfoo.so.1' from /etc/ld.so.preload cannot be preloaded (cannot open shared object file): ignored.
This causes resolve_deps() to return error, which leads to symlinks
(like usr/bin/awk) not being copied into the initrd.
Some modules are involved in the display output without to rely on
drm_crtc_init.
This is the case for the meson_dw_hdmi. This module need to be included
into the initramfs in both hostonly and generic modes.
Signed-off-by: Nicolas Chauvet <kwizart@gmail.com>
Daniel Molkentin