When in hostonly mode, 95fcoe module will still be installed even there
is no FCoE hostonly device. So use the new block_is_fcoe helper to check
for hostonly device in hostonly mode, avoid installing unneccessary module.
Signed-off-by: Kairui Song <kasong@redhat.com>
If fcoe module is loaded, the initramfs will always try load libfcoe
and bnx2fc, so also ensure they are installed if needed.
Signed-off-by: Kairui Song <kasong@redhat.com>
For the shell scripts, new environment variables were introduced.
dracutsysrootdir is the root directory, file existence checks use it.
DRACUT_LDCONFIG can override ldconfig with a different one that works
on the sysroot with foreign binaries.
DRACUT_LDD can override ldd with a different one that works
with foreign binaries.
DRACUT_TESTBIN can override /bin/sh. A cross-compiled sysroot
may use symlinks that are valid only when running on the target
so a real file must be provided that exist in the sysroot.
DRACUT_INSTALL now supports debugging dracut-install in itself
when run by dracut but without debugging the dracut scripts.
E.g. DRACUT_INSTALL="valgrind dracut-install or
DRACUT_INSTALL="dracut-install --debug".
DRACUT_COMPRESS_BZIP2, DRACUT_COMPRESS_LBZIP2, DRACUT_COMPRESS_LZMA,
DRACUT_COMPRESS_XZ, DRACUT_COMPRESS_GZIP, DRACUT_COMPRESS_PIGZ,
DRACUT_COMPRESS_LZOP, DRACUT_COMPRESS_ZSTD, DRACUT_COMPRESS_LZ4,
DRACUT_COMPRESS_CAT: All of the compression utilities may be
overridden, to support the native binaries in non-standard places.
DRACUT_ARCH overrides "uname -m".
SYSTEMD_VERSION overrides "systemd --version".
The dracut-install utility was overhauled to support sysroot via
a new option -r and fixes for clang-analyze. It supports
cross-compiler-ldd from
https://gist.github.com/jerome-pouiller/c403786c1394f53f44a3b61214489e6f
DRACUT_INSTALL_PATH was introduced so dracut-install can work with
a different PATH. In a cross-compiled environment (e.g. Yocto), PATH
points to natively built binaries that are not in the host's /bin,
/usr/bin, etc. dracut-install still needs plain /bin and /usr/bin
that are relative to the cross-compiled sysroot.
The hashmap pool allocate_tile/deallocate_tile code was removed
because clang-analyze showed errors in it. hashmap_copy was removed
because it wasn't used and clang-analyze showed errors in it.
DRACUT_INSTALL_LOG_TARGET and DRACUT_INSTALL_LOG_LEVEL were
introduced so dracut-install can use different settings from
DRACUT_LOG_TARGET and DRACUT_LOG_LEVEL.
Signed-off-by: Böszörményi Zoltán <zboszor@pr.hu>
Now that we are using persistent network names we can switch
to using the interface names when specifying the fcoe configuration.
With that we can print the fcoe configuration only once.
Signed-off-by: Hannes Reinecke <hare@suse.com>
We should be disabling the FCoE connection (which triggers sending
a LOGO internally) to logout from the target; this resets the target
and will avoid hitting a busy condition during reboots.
References: bsc#994860
Signed-off-by: Hannes Reinecke <hare@suse.com>
FCoE can run in Fabric (ie FCF) or VN2VN mode, so we should allowing
to set this parameter from the commandline, too.
Signed-off-by: Hannes Reinecke <hare@suse.com>
When lldpad is not running, any calls to 'dcbtool' will be printing
out a warning. As it perfectly legit to have FCoE running without
DCB we should not be printing out the error.
Signed-off-by: Hannes Reinecke <hare@suse.com>
If the installation already has a FCoE configuration we should
not attempt to overwrite it but rather use the pre-defined
configuration.
References: bsc#993861
Signed-off-by: Hannes Reinecke <hare@suse.com>
Some Combined Network Adapters(CNAs) implement DCB protocol
in firmware, it is recommended that do not run software-based
DCB or LLDP on CNAs that implement DCB, but we have to start
the lldpad service anyway(there might be other software DCB).
If the network interface provides hardware DCB/DCBX capabilities,
the field DCB_REQUIRED in "/etc/fcoe/cfg-xxx" is expected to
be set to "no".
We met an issue on "QLogic BCM57810" with DCB firmware support,
and found dracut still generated "fcoe=<mac>:dcb" which caused
kdump boot failure when using that fcoe dump target.
This patch parses /etc/fcoe/cfg-xxx to detect DCB_REQUIRED="no",
and force "nodcb" if it is the case.
Also improved some coding style in passing.
Signed-off-by: Xunlei Pang <xlpang@redhat.com>
lldpad is a system-wide process, which must be started only once.
So we should be separate it from fcoe-up, as it might be called
several times.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Thomas Renninger <trenn@suse.de>
When running with --hostonly-cmdline we should be storing
the current configuration in /etc/cmdline.d so that dracut
will be configure the system automatically.
References: bnc#877288
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Thomas Renninger <trenn@suse.de>
Add new functions require_binaries() and require_any_binary() to be used
in the check() section of module-setup.sh.
These functions print a warning line telling the user, which binary is
missing for the specific dracut module.
This unifies the way of checking for binaries and makes the life of an
initramfs creator easier, if he wants to find out why a specific dracut
module is not included in the initramfs.
Like -H, we need to poll every module to check if it is needed
to mount a specific device in '--mount'.
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
To start bnx2fc, we need to run fipvlan only and not dcbtool. DCBX is run
automatically in the hardware, but VLAN discovery needs to be started by
fipvlan.
https://bugzilla.redhat.com/show_bug.cgi?id=736094
Harald Hoyer